Model NO.: DSH 8
Layout Type: Verticle
Additional Capabilities: Drying, Granulating, Coating, Mixing
Operating type: Continuous Operating
Condition: New
Mixing Drum: Circular Groove
Feeding Rate: 0.4-0.6
Diameter of Mixing Materials: 40-3000
Load Factor: 0.4-0.6
Mixing Time: 4-10min
Operating: Cycle Operating
Trademark: WJ
Transport Package: Wooden Case
Specification: DSH 0.3/0.5/1/2-30
Origin: China
HS Code: 8419399010
Model NO.: DSH 8
Layout Type: Verticle
Additional Capabilities: Drying, Granulating, Coating, Mixing
Operating type: Continuous Operating
Condition: New
Mixing Drum: Circular Groove
Feeding Rate: 0.4-0.6
Diameter of Mixing Materials: 40-3000
Load Factor: 0.4-0.6
Mixing Time: 4-10min
Operating: Cycle Operating
Trademark: WJ
Transport Package: Wooden Case
Specification: DSH 0.3/0.5/1/2-30
Origin: China
HS Code: 8419399010
DSH Double Screw Cone Mixer machine equipmentÂ
Description
DSH double screw mixer integrates powder, granule and liquid mixing. The rotation of twin screw mixer is completed by a set of motors and cycloid reducers. With asymmetric mixing by two screws, the stirring range will be expanded and stirring speed will accelerate.
FeatureÂ
1.Homogeneous mixing
2.Short mixing time 5-15 minutes
3.Clean discharge &Â no leftover
4.Central discharge valve:
Electronic, pneumatic, manual (optional)
Ball valve, flap valve, knife gate valve, butterfly valve (optional)
5.Main shaft seal:Stuffing seal and air purge seal
6.Drive:Siemens motor, cycloid or gear reducer
7.Limit/safety switch (optional)
8.Heating/cooling jacket optional)
Helix cone mixer application:
1.Applicable material proportion of the poor, the powder particles are relatively large materials;
2.Suitable for ceramic glaze mixing gentle process, the material particles do not pressure-fed or broken;
3.The heat-sensitive materials will not overheat;
4.In the powder - powder mixing process is very easy to add working conditions or providing a liquid to a plurality of spray outlet means;
5.The bottom valve of dislocation convenient material, since the bottom of the spiral no fixtures, so there is no pressure fed phenomenon
Below Spec for Dry Powder Ribbon Mixer:
| Model | Total Capacity(CBM) | Loading factor | Motor Power(kw) | Dimention(Max diameter*Height)(mm) | Weight(kg) |
| DSH-0.06 | 0.06 | 0.4-0.6 | 1.5 | 630*1451 | 150 |
| DSH-0.1 | 0.1 | 1.5 | 715*1569 | 250 | |
| DSH-0.3 | 0.3 | 2.2 | 920*1960 | 550 | |
| DSH-0.5 | 0.5 | 3 | 1140*2320 | 600 | |
| DSH-1 | 1 | 4 | 1480*2898 | 1200 | |
| DSH-1.5 | 1.5 | 5.5 | 1633*3210 | 1350 | |
| DSH-2 | 2 | 5.5 | 1816*3495 | 1500 | |
| DSH-3 | 3 | 7.5 | 2040*3760 | 2300 | |
| DSH-4 | 4 | 11 | 2250*4425 | 2520 | |
| DSH-6 | 6 | 15 | 2548*4940 | 3000 | |
| DSH-8 | 8 | 18.5 | 2780*5360 | 4500 | |
| DSH-10 | 10 | 22 | 3018*5815 | 5500 | |
| DSH-12 | 12 | 22 | 3204*6100 | 5900 |
Â
 DSH Double Screw Cone Mixer machine equipment
Â
Description
DSH double screw mixer integrates powder, granule and liquid mixing. The rotation of twin screw mixer is completed by a set of motors and cycloid reducers. With asymmetric mixing by two screws, the stirring range will be expanded and stirring speed will accelerate.
FeatureÂ
1.Homogeneous mixing
2.Short mixing time 5-15 minutes
3.Clean discharge &Â no leftover
4.Central discharge valve:
Electronic, pneumatic, manual (optional)
Ball valve, flap valve, knife gate valve, butterfly valve (optional)
5.Main shaft seal:Stuffing seal and air purge seal
6.Drive:Siemens motor, cycloid or gear reducer
7.Limit/safety switch (optional)
8.Heating/cooling jacket optional)
Helix cone mixer application:
1.Applicable material proportion of the poor, the powder particles are relatively large materials;
2.Suitable for ceramic glaze mixing gentle process, the material particles do not pressure-fed or broken;
3.The heat-sensitive materials will not overheat;
4.In the powder - powder mixing process is very easy to add working conditions or providing a liquid to a plurality of spray outlet means;
5.The bottom valve of dislocation convenient material, since the bottom of the spiral no fixtures, so there is no pressure fed phenomenon
Below Spec for Dry Powder Ribbon Mixer:
| Model | Total Capacity(CBM) | Loading factor | Motor Power(kw) | Dimention(Max diameter*Height)(mm) | Weight(kg) |
| DSH-0.06 | 0.06 | 0.4-0.6 | 1.5 | 630*1451 | 150 |
| DSH-0.1 | 0.1 | 1.5 | 715*1569 | 250 | |
| DSH-0.3 | 0.3 | 2.2 | 920*1960 | 550 | |
| DSH-0.5 | 0.5 | 3 | 1140*2320 | 600 | |
| DSH-1 | 1 | 4 | 1480*2898 | 1200 | |
| DSH-1.5 | 1.5 | 5.5 | 1633*3210 | 1350 | |
| DSH-2 | 2 | 5.5 | 1816*3495 | 1500 | |
| DSH-3 | 3 | 7.5 | 2040*3760 | 2300 | |
| DSH-4 | 4 | 11 | 2250*4425 | 2520 | |
| DSH-6 | 6 | 15 | 2548*4940 | 3000 | |
| DSH-8 | 8 | 18.5 | 2780*5360 | 4500 | |
| DSH-10 | 10 | 22 | 3018*5815 | 5500 | |
| DSH-12 | 12 | 22 | 3204*6100 | 5900 |
Â
Â
Gildemeister Pipe Plasma Cutting Machine is mainly designed for Cutting different diameter Metal pipes .Machine build Big size Chuck and holding device to load heavy metal pipe ,with professional Plasma cutting controller to control rotary for a accurate metal pipe cutting work .If work doesn't require to cut less than 300 diameter metal pipe ,then a Table type Plasma cutting machine would be recommended as it allows operator cut more than just metal pipe but as well as flat metal sheet as well .
Cnc Gantry Plasma Metal Cutter,Small Cnc Plasma Machine Price,Cnc Plasma Pipe Cutting Machine,Plasma Round Pipe Cutter
Jinan Rapid CNC Machinery Co.,LTD , https://www.gildemeistercnc.com