Currently, concepts such as single-mode, dual-mode, tri-mode, and multi-mode in the market are more common in optical fibers. As with optical fibers, wireless bridges for transmitting information also have these “modesâ€. In the classification of “modesâ€, there are three types of wireless bridges: single-mode, dual-mode, and triple-mode.
So what are the single-mode, dual-mode, and triple-mode wireless bridges?
Here, for ease of understanding, the description will begin with the definition of single, double, and multimode optical fibers.
The so-called single-mode fiber has only one peak passing, which means that only one mode of fiber can be transmitted. Since the core of this type of optical fiber is very fine, about 8-10 microns, it forms a very small modal dispersion, so that the single-mode optical fiber can be transmitted over long distances over a wide frequency band.
Therefore, the characteristic of single-mode fiber is that it can only transmit one mode signal and has a long transmission distance.
A multimode fiber is an optical fiber with two or more transmission modes. Its fiber core is roughly 50-100 micrometers thick. Compared to a single-mode fiber, it will form a large modal dispersion, resulting in a shorter transmission distance. The loss increases, so it can only be used for short-distance, low-bandwidth signal transmission.
Therefore, multimode fiber is characterized by supporting multiple modes of signal transmission, but the transmission distance is short.
The single-mode, dual-mode, and tri-mode transmission modes that are converted into wireless bridges are wireless bridges that support one, two, and three signal transmission modes.
The difference between a wireless bridge and an optical fiber is that the former uses air as a transmission medium, and the latter uses an optical fiber as a transmission medium. When a wireless bridge performs long-distance wireless transmission, it needs a single-mode wireless bridge and needs to transmit simultaneously. When using two or three signal modes, you need to use dual-mode or three wireless bridges.
Therefore, the single-mode wireless bridge is characterized by supporting a mode of signal transmission with a long transmission distance.
The characteristics of dual-mode and tri-mode wireless bridges are that they support two or three modes of signal transmission, and the transmission distance is short. For example, a transit relay point can receive and transmit signals simultaneously using dual-mode and three-mode.
As shown in the figure below, the wireless bridge in the middle is a dual-mode wireless bridge ST5801GB-M, which is mainly used to receive the signal transmitted in front and forward the signal to the receiver at the rear.
Ship Building Steel Plate
Due to the harsh working environment of the ship, the hull shell is subject to chemical corrosion of seawater, electrochemical corrosion and corrosion of marine organisms and microorganisms; the hull is subjected to large wind and wave impacts and alternating loads; the shape of the ship is complicated by processing methods, etc. Steel for hull structure is strictly required. First of all, good toughness is the most critical requirement. In addition, high strength, good corrosion resistance, weldability, forming properties and surface quality are required.
Shipbuilding Steels Our hot rolled shipbuilding steel is produced in accordance with the relevant Classification Society, examples of which include Lloyds Register and Det Norske Veritas.
Our steel products include steel shipbuilding plate, fabricated steel sections and floor plate for decking. We can also supply bulb flats for plate stiffening, structural steel angles and inverted angles.
Our plates are supplied under the ASTM/ASME specification (ASTM A131 / ASME SA 131) which is the standard specification for Structural Steel for Ships. We offer higher strength shipbuilding steels as standard .High strength steels offer significant cost advantages by reducing the weight of the structure in comparison to the steel used.
The plates are suitable for use in the construction of container ships and large cargo freighters as well as commercial shipping lines such as luxury cruise ships and ferries. Supply options include heavy plates, surface treated plates and pre-fabricated sections. In most cases, the steel can also be supplied as hot rolled coils or cut into lengths (sheets).
These high yield materials are commonly used in the construction of hulls and superstructures for large shipping vessels. The grades are exclusively for shipbuilding use as set out in the standard.
Marine Steel Plate,Ccs Marine Steel Plate,Ship Building Steel Plate,Ah36 Marine Steel Plate
Shandong Guanzhou Iron and Steel Group Co., Ltd , https://www.shansteelsupply.com
