The dome on the market is also more widely applied, but the use of the process there will be at fault, the following gave you share it!
1. The dome is powered on, no action, no image, and the indicator is off. Check if the power cord is connected incorrectly. If the connection is incorrect, connect the power cord according to the correct method. Check whether the power supply is damaged: If the power supply is damaged, replace it to ensure that the power supply is not damaged. Check if the fuse is damaged: If it is damaged, replace it to ensure that the fuse is not damaged. Check the power cord for poor contact: If it does not contact properly, reconnect the power cord or replace the power cord.
2, the power self-test, an image can not be controlled check ball machine address code, baud rate setting is wrong: Set if any error codes that matches the address and baud rate. Check whether the protocol settings are correct: If yes, set the corresponding protocol. Check whether the RS485 control cable is connected correctly: If it is incorrect, connect it according to the correct method.
3, self-test can not be carried out, there are images but accompanied by noise testing whether mechanical failure: Please correct the mechanical structure of the dome, such as the camera tilt please correct. The power may not be enough: Please replace the power supply that meets the requirements and try to place the switching power supply near the dome.
4ã€Unstable image Replace the qualified video cable to check if the video cable is in poor contact. The power may not be enough: Please replace the power supply that meets the requirements and put the switching power supply near the dome.
5, the screen blur may focus on the manual state, control the dome or call any preset position, the dome can resume auto focus. The transparent cover is dirty and the transparent cover is cleaned.
6, the control ball machine stop or delay the inspection control dome farthest matching resistance is added, if not added in the remote control unit from the ball, join matching resistor. The power may not be enough: Please replace the power supply that meets the requirements, and place the switching power supply near the dome.
1. The dome is powered on, no action, no image, and the indicator is off. Check if the power cord is connected incorrectly. If the connection is incorrect, connect the power cord according to the correct method. Check whether the power supply is damaged: If the power supply is damaged, replace it to ensure that the power supply is not damaged. Check if the fuse is damaged: If it is damaged, replace it to ensure that the fuse is not damaged. Check the power cord for poor contact: If it does not contact properly, reconnect the power cord or replace the power cord.
2, the power self-test, an image can not be controlled check ball machine address code, baud rate setting is wrong: Set if any error codes that matches the address and baud rate. Check whether the protocol settings are correct: If yes, set the corresponding protocol. Check whether the RS485 control cable is connected correctly: If it is incorrect, connect it according to the correct method.
3, self-test can not be carried out, there are images but accompanied by noise testing whether mechanical failure: Please correct the mechanical structure of the dome, such as the camera tilt please correct. The power may not be enough: Please replace the power supply that meets the requirements and try to place the switching power supply near the dome.
4ã€Unstable image Replace the qualified video cable to check if the video cable is in poor contact. The power may not be enough: Please replace the power supply that meets the requirements and put the switching power supply near the dome.
5, the screen blur may focus on the manual state, control the dome or call any preset position, the dome can resume auto focus. The transparent cover is dirty and the transparent cover is cleaned.
6, the control ball machine stop or delay the inspection control dome farthest matching resistance is added, if not added in the remote control unit from the ball, join matching resistor. The power may not be enough: Please replace the power supply that meets the requirements, and place the switching power supply near the dome.
Yoga mats and exercise mats are a hot topic right now – how else are you going to smash those self-isolation home workouts?
From protecting your joints from injury on hard surfaces mid workout to keeping you steady and stable during yoga asanas and providing a softer surface to lower down to during chest-to floor burpees (vom), a gym mat is the bread and butter of a great exercise kit. Now that we're all spending much more time 'en casa' there's never been a better time to invest.
Yoga Mat,Travel Yoga Mat,Yoga Mat Foldable,Exercise Floor Mat
Shaoxing geili sports and leisure goods Co.,Ltd , https://www.geilisports.com